How to Make a Kitchen Island With Base Cabinets

How to Make a Kitchen Island With Base Cabinets – Everybody wants more space in their own kitchen and one approach to make this space is to devote a peninsula. This easy project is not hard to create and will enlarge countertops, eating and storage space. How to make a kitchen island with base cabinets?

How to Make a Kitchen Island With Base Cabinets

The base of the peninsula is constructed from three top cabinets and 1 corner cupboard to make an L-shaped accession. How to make a kitchen island with base cabinets such as top cupboards are 12-inches hefty and usually found above countertops, however, rather than using the normal 24-inch heavy lower cupboards, these can occupy much less space whilst still creating additional storage.

Step 1 - How to Make a Kitchen Island With Base Cabinets Materials and Tools:

  • Three 12-Inch Upper Cabinets
  • One Circle Cabinet
  • 2x4s for Toe Kicks
  • Cabinet Screws
  • MDF Countertop
  • Laminate
  • Get Cement
  • Spacers
  • Clamps
  • Measuring Tape
  • Drill
  • Circular Saw
  • Laminate Slitter
  • Router and Laminate Bit
  • J-Roller
  • Contact Cement Rollers
  • Security Glasses

Step 2 - How to Make a Kitchen Island With Base Cabinets Step by Step:

  1. Construct the cabinets upside down and quantify. Clamp the cupboards and mix with screws.
  2. Since upper cupboards don’t necessarily include a toe-kick, a person will need to be built. This project calls to get an abysmal toe kick. The toe-kick should be assembled so that it remains 3 inches on either side of measures and the cupboards 4 inches greater. Place spacers through the toe kick over the points at which the cabinets match.
  3. When assembled, twist the toe-kick spacers into the cupboard.
  4. Twist the peninsula right-side-up and put it. Twist the peninsula cabinets into your preexisting ones.
  5. Place the MDF countertop. The countertop ought to hang two inches above the doorway side and two inches across the buttocks. The overhang at the bottom is likely to create extra chairs space. Out of screwing throughout the cabinets twist the countertop.
  6. Assess the width and length of this countertop and apply the laminate. You would like to bring an inch allowing your area when attaching the laminate. Cut from the laminate with a saw.
  7. Utilize a laminate stripper to decrease laminate to all those surfaces of the countertops. Clip an inch bigger than measurements.
  8. Get ready to place the laminate flooring. Apparent the surface and make sure that there isn’t any dust or debris. Apply two coats of contact cement to the bottom of the strips into the counter sides and a coat. Permit the contact to wash afterward carefully place the strips. Be cautious that when the laminate is initiated, it can not be transferred. Roll out a few air pockets utilizing a J-roller.
  9. When it’s completely dry, then apply the router and also a laminate slice to eliminate the surplus laminate. Place of the router on the counter’s face and continue in a left to right movement.
  10. If all of the surplus laminate is removed, now is the time to begin working on the countertop. Again, add two coats of contact cement to the countertop and a single coat into the base of the flooring.
  11. Place spacers down no longer than a foot when the contact cement has dried. Twist the laminate is positioned. Once set up, you will not have the ability to fix it, bear in mind. Remove at a moment, and smooth the laminate using out the J-roller.
  12. After all has dried, then place the router into the process and counter left-to-right’s bottom to get rid of the laminate.
  13. Add a backing that is attractive. Beadboard which was Painted was used in this case.
See Also:  Passive Solar Home Design Plans

Step 3 - How to Make a Kitchen Island With Base Cabinets

error: Content is protected !!