How to Build a Pool Table Step by Step

How to Build a Pool Table – The pool table within this project is constructed largely of medium-density fiberboard (MDF) since it is hardy and inexpensive. The base is fitted with a grid to conserve the top. The table consists of built-in compartments to your rack, cue sticks, along with billiard-ball tray. Walnut railings along with a glowing sensed cover with gold trimming add some type.

DIY Build - How to Build a Pool Table Materials: (How to construct a Pool Table)

  • Five sheets of 4-by-81/2-inch medium-density fiberboard
  • Five sheets of 4-by-83/4-inch medium-density fiberboard
  • Five walnut planks measuring 8 feet by 8 inches from 3/4-inch
  • three walnut planks measuring eight ft by 8 inches out of 3/4-inch
  • Five 8-foot walnut 2-by-4-inch planks
  • 9-foot precut felt railings and mattress (bright red)
  • 2 16.5-oz headphones of high-strength spray glue
  • Six K-66-style 9-foot cushions (rubber bumpers), cut match for your project
  • Six Western-style tooled-leather pool pockets
  • Billiard accessory kit (includes pool ballsand wooden horn, brushes, plus four cue sticks, cue chalks, pool-table pay)
  • 1 mill of dark brown latex paint
  • 1 roster of 1/2- or 3/4-inch-wide white paper tape
  • 2 cans of gold spray paint
  • 1 gallon of primer
  • One will obviously wealthy brown furniture wax.

Build - How to Build a Pool Table Tools: (How to construct a Pool Table)

  • Table watched
  • Chop saw
  • Band saw
  • Jigsaw
  • Hole discovered
  • Guide saw
  • Router
  • fur fur and claws
  • Stapler and staples
  • Wood glue
  • Five to 10 wood knobs
  • Lathe
  • Chisels
  • Sandpaper
  • Orbital Sander
  • Drill
  • Screws
  • Biscuit Joiner
  • Upgrades
  • Drill press
  • Planers
  • Measuring tape
  • Disposable brushes
  • Shop towels
  • Razor blade

 width= Dimensions: (How to Build a Pool Table)

  • Surface (playing area) complete: 31/2 feet by 7 feet
  • Tapered sides: 5 inches by 10 inches by 1 ft high
  • Complete leg dimensions: 6 inches out of 113/4 inches by 16 inches shirt
  • Bun also: 3 inches high by 10 inches around
  • Bun at foundation: 3 inches high by 5 inches round
  • Molding: two inches wide
  • Square (routered) shirt: 1 ft
  • Square (routered) bottom: 6 inches
  • Tapered Sides of Table:
  • Long sides: 6 ft by 6 inches by 13 inches shirt
  • Short sides: 4 ft by 13 inches shirt
  • Molding: two inches broad
  • Ball holster/slot: 37 inches wide by 3 inches high
  • Holes (six inches): 4 7/8-inch gap working with a 1/4-inch lip (round-over piece for your router)
  • Rails: two3/4 inches (upper horizontal surface) wide by 4 to 5 inches high
  • Rubber bumpers: 49-inch lengths (cut to fit); complete dimensions 1.177 inches in 0.968-inch.

Pool Table Light - How to Build a Pool Table Step by Step: (How to construct a Pool Table)

  • employing a table saw and chop saw, cut 1/2-inch 4-by-8-foot medium-density fiberboard (MDF) sheets to the back faces of those four arms (only a couple of the equal side to every leg). There’s not any particular angle into the taper. Cut an opening in the center of the replicate facet of each leg by means of a band saw, which creates a 2-inch rim (it looks like a framework).
  • Cut two 3/4-inch MDF squares for every single leg – that the shirt is actually a 1-foot squarefoot, and the base is genuinely a 6-inch square – and - router that the boundaries. Cut bamboo boards to strips to coincide with the four corners of their sides that are tapered. Router the strips, mimicking the squares. Everything for those legs should be glued and nailed into position.
  • For the ideal bun, cut and paste three 3/4-inch-by-10-inch squares to some block. Clamp and let dry. Cut a circle out of this cube (10-inch diameter). Employing a router in addition to a lathe, create a convex border on the bun. For your foundation bun, follow precisely the identical procedure, but use three 3/4-inch-by-7-inch squares also shape a concave edge onto the bun. Sand necessary. Glue and nail all in to position. Repeat procedure for many legs.
  • To make the tapered sides, then cut 78-by-13-inch MDF pieces, following the angle of their thighs. Cut the 2-inch-wide molding out of two of those four bits. The MDF pieces that are comprehensive are then gone over by the molding. Repeat the process for those endings, but utilize 48-by-13-inch bits, and correct dimensions accordingly. Apply pine strips step two explains. Glue and nail into position.

Plank and Hide - How to Build a Pool Table

  • Once the sides are together, glue and nail 1-inch MDF strips to the inside edge of each corner.
  • Over a few of the more sides of this desk, centered, cut on a 37-by-3-inch rectangle in prep for your ball slot machine. This eliminated part will grow to be this chunk slot, place in the desk’s back wall. For the outdoor, cut off a rectangle framework out of pine strips: the lightest strip is only 1 inch wide and approximately 1/2-inch out both sides of the rectangle pit; another side will be 1/2-inch broad in addition to the elevation of this gap; the underside protrudes approximately 2 inches and inches around grip the balls. Router the boundaries. The front-most border is going to probably be 1/2-inch thick. Glue and nail into position.
  • To find assistance, add 2-by-4’s around the period of the foundation of how to build a pool table.
  • Along with the ball stand on the right, with a hole saw, drill four1/2-inch-wide holes spaced 1 inch apart from the short end of this desk, and 3 inches above the bottom molding.
  • Each pit includes a three-sided rectangular framework inside the desk to hold the clues. The parts are 3 inches wide and about 60 inches long and are trimmed from 3/4-inch MDF. Nail and glue the elements within the desk enclosing every hole so and into position.
  • Cut a 3-inch-high, 1-foot-wide rectangle of MDF two inches over the holes into the hints. Into a 9-inch-long, 14-inch-wide method, you glue and may nail in the bottom edge of this pit to maintain the horn. To hold both surfaces of the triangle nail snugly between both these pieces.
  • Cut four pre-assembled bits (approximately 3 inches) of 3/4-inch walnut to act as guides to each location over the corners ). Find turn at the guides, and persistent leg positions so the legs consistently find their place. Sand everything gently with sandpaper along with an orbital sander.
  • Cut a 3/4-inch sheet of MDF to coincide with the cover of the table with a circular saw; it can enlarge 6 inches on each side (such as your railing along with bumper). With a jigsaw, cut six holes at the MDF (four corners, two in centers of long sides) at 4 7/8 inches and then shaped in a half-circle. The overall angle of these holes is 90 degrees, to adapt the railings. Create a template to get a corner pocket and also a centre pocket, and follow it. Router the interior edge of each pocket to balls.
See Also:  Homemade Carpenter Bee Trap Plans Building

Pool - How to Build a Pool Table

  • The railings are made from pine boards. Each rail component is triple-segmented to mimic a curve in behind the table, moving. The very best rail piece is two3/4 inches broad, the bit that is angled is simply 11/2 inches, and also the bit is 4 inches to five inches. An additional inner bit (approximately 1 inch square to the finish) that can hide underneath the railings will aid in attaching the rails into the dining table. There’ll be six railroad segments, a couple of the exact same (the endings) and four of exactly the same (the sides) (roughly 3 ft for each). Attach the railings with a biscuit joiner and glue. Clamp them and set to dry.
  • Twist the MDF table above as well as with walnut, then form a honeycomb pattern that comprises 10-inch squares. Center this routine round the MDF. This will help match it readily and also can act as service for the dining table.
  • Primer the exterior to get a base coating, minus the railings and also the tabletop.
  • Unclamp the railings which are dried. Smooth the curve utilizing planers, a foundation and also a router. Utilize an orbital sander. Cut the railings into segments. Drill holes to choose the bolts of those pockets inside every single pocket (12 holes pristine). Construct a jig for consistency, with a drill press on those holes. Try trimming or sand as vital, and a match of the pockets as well as the railings .
  • Disassemble any linking rails, rub ample brown furniture wax onto the railings, and then paint the base of the table (thighs and base) using darkish brown latex paint.
  • Cut using a razor and extend the crimson felt round the desk, smoothing it maneuver, and spray-glue it into position. Staple it all around the sides for additional support.
  • Begin to construct the pockets and railings working your way around the perimeter. Function in sections. Use the pocket magnets until they’re comfortable and then twist the pockets in the ground up. Attach and pockets to the table with spray glue of how to build a pool table, and nails.
  • Cut the rubber bumpers to coincide with the pockets. Stretch red felt then and then staple them , and paste spray-glue them into position.
  • In the routered edges and interior edges of the underside painted portion of the dining table cut and use bits of white paper tape that’s been spray-painted gold.

error: Content is protected !!